ipw3945
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
ipw3945 [2007/06/09 19:49] – darkaudax | ipw3945 [2017/01/09 21:28] (current) – Mark page as deprecated. mister_x | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== DEPRECATED ====== | ||
+ | |||
+ | **IMPORTANT NOTE**: This page is deprecated, updated documentation can be found [[install_drivers|here]] | ||
+ | |||
====== ipw3945 ====== | ====== ipw3945 ====== | ||
- | At this point in time, this page is far from complete. | + | //Note: This page is about the ipw3945/ |
+ | |||
+ | ===== Injection Walkthrough ===== | ||
+ | |||
+ | This is for an intel PRO/ | ||
+ | |||
+ | I've tested this on [[http:// | ||
+ | |||
+ | You need a Internet Connection with your LAN Cabel. | ||
+ | |||
+ | Open a Terminal and type... | ||
+ | |||
+ | **Pre requirements** | ||
+ | < | ||
+ | sudo apt-get install build-essential | ||
+ | sudo apt-get install libssl-dev | ||
+ | </ | ||
+ | |||
+ | // For openSUSE and other RPM-based distros, this is different (replace " | ||
+ | < | ||
+ | sudo zypper install gcc | ||
+ | sudo zypper install libopenssl-devel | ||
+ | </ | ||
+ | |||
+ | |||
+ | **Installation** | ||
+ | |||
+ | * Download ipwraw-ng from http:// | ||
+ | |||
+ | * Install the modules and ucode | ||
+ | |||
+ | * Blacklist ipwraw (so it's not automatically loaded at boot time) | ||
+ | |||
+ | < | ||
+ | wget http:// | ||
+ | tar -xjf ipwraw-ng* | ||
+ | cd ipwraw-ng | ||
+ | make | ||
+ | sudo make install | ||
+ | sudo make install_ucode | ||
+ | echo " | ||
+ | sudo depmod -ae | ||
+ | </ | ||
+ | |||
+ | **Use ipwraw-ng** | ||
+ | |||
+ | * Unload the ipw3945 module | ||
+ | * Load ipwraw-ng | ||
+ | |||
+ | The device created will automatically be in monitor mode. | ||
+ | |||
+ | < | ||
+ | sudo modprobe -r ipw3945 | ||
+ | sudo modprobe ipwraw | ||
+ | </ | ||
+ | |||
+ | The new device name for injection should should be called wifi0 and the monitor interface should be rtap0. | ||
+ | |||
+ | < | ||
+ | lo no wireless extensions. | ||
+ | |||
+ | eth0 no wireless extensions. | ||
+ | |||
+ | wifi0 | ||
+ | Mode: | ||
+ | |||
+ | rtap0 no wireless extensions.</ | ||
+ | |||
+ | |||
+ | IMPORTANT before using airodump-ng you need to : | ||
+ | # ifconfig wifi0 up | ||
+ | |||
+ | **Configure your Wireless Card** | ||
+ | |||
+ | You can use iwconfig to set the channel and rate and transfer power. | ||
+ | |||
+ | < | ||
+ | iwconfig eth1 channel 11 (on which you want to sniff) | ||
+ | iwconfig eth1 rate 1M (min=1M and max=54M) | ||
+ | iwconfig eth1 txpower 16 (min=-12 and max=16) | ||
+ | </ | ||
+ | |||
+ | And when you're done, | ||
+ | |||
+ | < | ||
+ | sudo modprobe -r ipwraw | ||
+ | sudo modprobe ipw3945 | ||
+ | </ | ||
+ | |||
+ | ===== Useful Links / Info ===== | ||
+ | |||
+ | At this point in time, this page is far from complete. | ||
Useful links: | Useful links: | ||
- | * [[http://tinyshell.be/aircrackng/ | + | * Thread: |
- | * [[http:// | + | * Thread: [[http://forum.aircrack-ng.org/ |
+ | * Thread: | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | Also consider using the [[links# |
ipw3945.txt · Last modified: 2017/01/09 21:28 by mister_x